Preference for the type of Crusher

Material to be crushed

Bulk Density of Material (t/m³)

Capacity (Rated/Designed), tph

Compressive strength of material (MPa)

Bond Work Index / Hard groove Index

Moisture content (%)

Feed Size (Top size and 80% passing), mm

Product size (80% passing)/ Separation size (For Rotary Breaker Only), mm

Open / Closed circuit

Provide flow sheet/layout, if possible

% of Product size in feed

Material to be Screened

Bulk Density of Material (t/m³)

Capacity (Rated/ Design), tph

Moisture content in Feed (%)

Feed Size Analysis

Preference of screening decks (Perforated plate/ PU / Woven wire mesh / wedge wire/ Rubber/ Stainless Steel) (For Circular /Linear Motion Screen)

Separation Size/ sizes ,mm

Type of screening process(Dry or Wet) (For Circular /Linear Motion Screen)

Preferred Type of screen (Circular motion/ Linear motion/ Flip Flow)

Desired screening efficiency

Type Of Feeding

Provide flow sheet/layout drawing, if available

Material to be ground

Specific Gravity of material

Bond Work Index (Kwh/st) or (Kwh/Mt)

Moisture content (%) in case of dry grinding

80% passing feed size

80% passing product size

Fresh feed rate, tph

Type of grinding circuit (open / closed)

Name of liquid in case of wet grinding

Specific gravity of liquid in case of wet grinding

Provide flow sheet, if possible

Material Handled

Lump Size (Maximum), mm

Bulk Density of material (t/m³)

Rated Capacity, tph

Moisture Content (%)

Hopper Opening ( L X W ) at Top & Bottom.

Location

Inclination

Height of Fall

Center to Center Distance

Provide flow sheet, if possible

Technical Requirement of PAN Material , Type of chain, Type of Drive- Electromechanical / Hydraulic /any specific requirement

Dribble Conveyor required or not

Material Handled

Lump Size (Maximum), mm

Bulk Density of material (t/m³)

Capacity (Designed & Rated), tph

Moisture Content (%)

Hopper Opening ( L X W ) at Top & Bottom. OR Hopper Load

Technical Requirement of Type of DRIVE - Electromechanical/ Hydraulic

Material to be Handled

Bulk Density of material (t/m³)

Capacity Design/Rated ,tph

Moisture content in Feed (%)

Lump Size (Maximum), mm

Separation Size & % passing (For Grizzly Feeder)

Preference of MOC of Deck /Grizzly

Type Of Feeding

Location

Material Handled

Feed Size

Capacity TPH

Bulk Density

Moisture

Fixed Speed/Variable Speed

Open / closed circuit

Provide flow sheet/layout, if possible

Belt width

Capacity (Rated / Design)

Material Handled

Lump Size

Tripper inclination

Tripper Travel

Top of belt from Floor

Top of rail from Floor

Rail size

Rail CRS

Top of Discharge Pulley from Floor

Discharge & Bend Pulley Diameter

Shaft diameter at Bearing of above

Face width of above

Bearing CRS of above

Type of Discharge (1-way/2-way/3-way)

Type of Gate, if provided in Discharge Chute

C/C distance of Bunker slot

Cross section of Discharge Chute

Width of Bunker slot

Width of Bunker sealing Belt

Idler Roll dia

Idler Height

Belt Tension at Discharge Pulley at two extremities of travel

Power feeding arrangement (CRD/Festoon cable)

Type of Rail Clamp

Type of Brake

Are MOC of components mentioned in NIT? If yes, provide details

What is the Drive arrangement as per NIT? Provide details

Approved List of Make of Bought-out components

Capacity (m3/hr):

Total Discharge head (mwc):

Specific Gravity of Slurry:

Percent of Solid by weight:

Maximum particle size in slurry (mm/micron):

Suction should be flooded:

Any pH value of slurry:

Temperature of slurry:

Viscosity of slurry:

>

What is slurry to be pumped:

Forth Factor:

Sump depth (mm) :

Speed (rpm)

Material to be handled

Specific Gravity of material

Bulk Density (t/m³)

Fresh feed rate (tph)

Feed size analysis

Provide flow sheet, if possible

Clay % in feed

Ore Up gradation Desired

Slurry to be handled:

Duty: Continuous/ Intermediate

Sieve analysis (Minimum 3 size fraction):

Dry solids (Tonnes/hr):

Specific Gravity of solids:

Specific Gravity of slurry:

Percentage of solid by weight in feed:

pH of slurry:

Temperature of feed slurry:

Capacity of feed slurry (m3/hr):

Material to be crushed & application e.g. Mines, Power plant etc.

Bulk Density (t/m³)

Moisture - average / max. (%)

If ROM Coal, approx. percentage of Shale and Sandstone

Bond Index (kWh/t) or Hard groove Index

Feed analysis or Average feed size, say 80% passing size (mm)

Max. Lump size (max. edge/diagonal length) present in feed (mm)

Desired product size (mm)

Any limitation in fines generation desired

Fresh Feed rate/ Capacity (tph)

Feeding method (dumper size, if by dumper)

No. of working shifts/day

Purpose of enquiry (Budgetary, Purchase, Feasibility report etc.)

Material to be crushed & application e.g. construction, Road etc.

Bulk Density (t/m³)

Moisture - average / max. (%)

Bond Index (kWh/t) / Hard groove Index/ Compressive strength (MPa)

Feed analysis with percentage of product / undersize present in the feed

Max. Lump size (max. edge/diagonal length) present in feed (mm)

Desired product size (mm)

Fresh feed rate/capacity (tph)

Size and percentage of Natural Fines/ Clay, if removal is required

Feeding method (dumper size, if by dumper)

No. of working shifts/day

Purpose of enquiry (Budgetary, Purchase, Feasibility report etc.)

Type of plant required – Stationary or mobile

Capacity (Stationary Plant) – 160/240 TPH

Capacity (Mobile Plant) – 90-120 TPH

No. of Aggregate Hopper – 4 / 5 / 6

Aggregate Hopper Capacity – 15 / 20 / 30 Cum

Bitumen Tank Capacity – 30000 / 40000 / 50000 Ltr

Diesel oil tank Capacity -10000 / 30000 Ltr

Heavy oil tank capacity – 30000 / 50000 Ltr

Burner – Dual /single ( LDO / Fuel oil )

Plant Capacity – 60/90/120/150/200 Cum/ Hr

Application – Building / Road / Railway / Pavement / Dam

No. of Aggregate Hopper – 3 / 4 / 5

Aggregate Hopper Capacity – 15 / 20 / 30 Cum

Type of Aggregate Feeding Conveyor - Flat Belt / Trough Belt / Chevron Belt / Skip

Type of Mixer – Twin Shaft / Twin Shaft Spiral

Capacity of Plant – 10 / 20 / 30 /50 TPH

Annual Requirement in Tons

What kind of Mortar to be manufactured – General ( Masonry, Plaster Ground ) and Special ( Tile Adhesive, Tile Grout, Water proof, Decorative mortar )

Type of plant – Station / Tower / Stair / Customized

Finished product packing mode – Bags / Bulker

Type of fuel to be used to dry the sand – LDO / Fuel Oil / Coal / natural gas

Plant Capacity – 50 /75/100 Cum/ Hr

Application – Building / Road / Railway / pavement / Dam

Aggregate Hoppers – 4 bin system / 2 bin system

Aggregate Hopper capacity – 7.5 / 15 Cum

Type of Mixer – Twin Shaft / Twin Shaft Spiral

Query